HEMPEL'S SHOPPRIMER E 15280
BASE：15289
CURING AGENT：95270

Description:
HEMPEL’S SHOPPRIMER E 15280 is a two-component epoxy primer, pigmented with zincphosphate rust-inhibiting pigments. It is designed for automatic spray application as well as manual application.

Recommended use:
As a shopprimer for protection of blast cleaned steel plate and other structural steel during the storage and building period.

Service temperature:
Maximum, dry exposure only: 140°C/284°F

Certificates/Approvals:
Approved as a welding primer by Lloyd's Register of Shipping. Approved as a welding primer by Det
Norske Veritas
Tested for non-toxicity of welding fumes by the Danish Welding Institute
Complies with European Fire Standard EN 13501-1; classification B-s1, d0.

Availability:
Part of Group Assortment. Local availability subject to confirmation.

PHYSICAL CONSTANTS:
Shade nos/Colours：50890 / Red.
Finish：Flat
Volume solids, %：22 ± 1
Theoretical spreading rate：11 m2/l [441.1 sq.ft./US gallon] - 20 micron/0.8 mils
Flash point：-4 °C [24.8 °F]
Specific gravity：1.1 kg/litre [9.1 lbs/US gallon]
Dry to handle: 5 - 10 minute(s) 20°C/68°F
Fully cured：7 day(s) 20°C/68°F
VOC content：658 g/l [5.5 lbs/US gallon]
                        The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.

APPLICATION DETAILS:
Version, mixed product：15280
Mixing ratio：BASE 15289: CURING AGENT 95270
                       2 : 1 by volume
Application method：Airless spray / Air spray / Brush
Thinner (max.vol.)：08570 (20%) / 08570 (20%) / 08450 (20%) see REMARKS overleaf
Pot life：8 hour(s) 20°C/68°F
Nozzle orifice：0.021 "
Nozzle pressure：75 bar [1087.5 psi]
                           （Airless spray data are indicative and subject to adjustment）
Cleaning of tools：HEMPEL'S TOOL CLEANER 99610
Indicated film thickness, dry：20 micron [0.8 mils] see REMARKS overleaf
Indicated film thickness, wet：Not relevant
Overcoat interval, min：see REMARKS overleaf
Overcoat interval, max：see REMARKS overleaf

Safety：
Handle with care. Before and during use, observe all safety labels on packaging and paint containers,consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.

SURFACE PREPARATION:
Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other contaminants by high pressure fresh water cleaning. Abrasive blasting to Sa 2? (ISO 8501-1:2007). Apply immediately after cleaning. All damage of shopprimer and contamination from storage and fabrication should be thoroughly cleaned prior to overcoating. For repair and touch-up use: primer specified for final coating system.

APPLICATION CONDITIONS:

Use only where application and curing can proceed at temperatures above: 10°C/50°F. The temperature of the surface and that of the paint itself must also be above this limit. Maximum steel temperature approximately: 45°C/113°F. Special measures must be taken for shopprimer applications at temperatures above app.: 45°C/113°F. (see REMARKS below).
Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation.
In confined spaces provide adequate ventilation during application and drying.

PRECEDING COAT:
None.

SUBSEQUENT COAT:
According to specification.

REMARKS:
Film thicknesses/thinning:
When applied at higher temperatures extra thinning or use of thinner with slower flash-off time may be needed to secure proper paint film formation. It is a must that a homogenous and smooth paint film is obtained.
Recommended dry film thickness: 15 - 25 micron / 0.6 - 1 mils measured on a smooth test panel.

Overcoating:
Overcoating intervals related to later conditions of exposure: If the maximum overcoating interval is exceeded, roughening of the surface is necessary to ensure intercoat adhesion.
Before overcoating after exposure in contaminated environment, clean the surface thoroughly with high pressure fresh water hosing and allow drying.

Overcoating note:
Before overcoating after exposure in contaminated environment, clean the surface thoroughly by high pressure water cleaning and allow drying.

Overcoating intervals:
No maximum overcoat interval for adhesion, but dictated by gradual breakdown and damage during exposure and fabrication.

Note:
HEMPEL'S SHOPPRIMER E 15280 For professional use only.

返回